RIVAGE PM Firmware V3.00 (Previous version)

Use this file to update the RIVAGE PM system to V3.00. Please read the following instructions carefully before updating.

In the RIVAGE PM firmware V3.0, we found a problem in which the control surface might freeze when channel parameters are copied using the [COPY] and [PASTE] keys in the hardware Selected Channel section. Use the touch screen, RIVAGE PM EDITOR or RIVAGE PM StageMix to copy channel parameters and avoid using the keys in the Selected Channel section for this operation until the fixed version is released. If this problem occurs, reset the control surface using the [RESET] switch in the rear panel of the control surface. Any audio including the input from the OMNI IN jack and output to the OMNI OUT jack will not be interrupted while the control surface is being reset.

RIVAGE PM Firmware / Editor Compatibility

Please make sure to match all versions of CS-R10, CS-R10-S, CSD-R7, DSP-R10, RPio622, RPio222, and RIVAGE PM Editor when you operate the RIVAGE PM system. Using an unsupported Editor/firmware combination may result in unexpected behavior. When updating, a TWINLANe network card (HY256-TL, HY256-TL-SMF) must be installed into the corresponding slot in order to update them simultaneously. If any additional cards are installed after performing the update, please execute the update program again. For a Dante card (HY144-D, HY144-D-SRC), use the Dante Firmware Update Manager to perform the update.

Compatibility List

New features in V3.00

Labeling function for device names, slots, and ports of network-connected devices. The labels can be found in locations such as the Patch window.
Parameter selection when copying channel parameters. In addition, inserted plug-ins also can be copied when copying channels.
Added level metering points (PRE GC and PRE D.GAIN for the INPUT METER).
Added the “DaNSe” plug-in, a 6-band noise suppressor “DaNSe” which removes background noise and unwanted reverberation.
MixToInput function for signal loopback from MIX/MATRIX busses to input channels.
SUB IN function to patch from input channels to output channels.
Easy-to-use preset for DCA assigning in the THEATRE MODE.
Attenuator for each EQ bank.
Display of the EQ type in the EQ graph.
Alert message when loading data different from the current system configuration.
WITH SYSTEM SETTING button for loading the following settings when loading ALL data.
- Wordclock setting
- DANTE SETUP (including device mounting, patching, and port names)
- RY-Slot settings of RPio622/RPio222 (including card settings)
- Network settings (HY-Slot and RIVAGE PM StageMix)
- +48V MASTER
Added parameter set items when touching parameters while pressing the [SHIFT] key to set up multiple channels simultaneously.
- STEREO A/B on and off in input channels and MIX channels
- Bank links on and off for EQ and Dynamics in the THEATRE MOTE
Sort function in the Library screen.
Display of the internal latency of the engine related to the Delay Compensation setting.
RTA offset function to display in linear fashion.
Selection for the [ON] key operation in the SENDS ON FADER mode.
Flashing of the ON button of the muted channel by mute group function in the SELECTED CHANNEL VIEW screen or the METER screen.
[SHIFT] key settings to select whether the action is applied to each BAY or to all BAYs.
Determination via the [ENTER] key instead of the ON button when entering settings via the keyboard.
Added assignable functions for the USER DEFINED keys, USER DEFINED knobs, and the [Fn] key.
- USER DEFINED keys
  - SPECIFIC CH of INPUT A/B
  - BAY ALL for the SET BY SEL, SET NORMAL VALUE, and OSCILLATOR
  - SOLO ON
- USER DEFINED knobs
  - SPECIFIC CH of CH FADER
- [Fn] key
  - VSC ON

Improvements in V3.00

Operability and visibility of settings on the FOCUS, GLOBAL PASTE and RECALL SAFE screens.
Operability of settings on the CUSTOM FADER BANK popup screen.
Operability of direction of data synchronization on the DEVICE SYNC screen.
Display of the channel name on such as the Patch screen or METER screen to improve operability and visibility.
Reduced variation of MIDI/GPI output time in a scene recall.
Changed the signal level from a stereo MIX channel to the STEREO bus to nominal when PAN is set to maximum.
The last function is displayed when assigning a function to an empty USER DEFINED key or knob.
SEND MASTER display will relate to output channel selection.
Displayed as "DEVICE NOT SYNCED!" when there is a device that cannot sync in the TWINLANe network.

Fixed Bugs in V3.00

Solved a problem in which the variable range of SEND level via the SEND knob of the Selected Channel section might not have been appropriate.
Solved a problem in which the FILTER Q indication did not appear on the Selected Channel section when DYNAMICS was set to DE-ESSER.
Solved a problem of the THEATRE MODE in which EQ or DYNAMICS differed when channels were paired via a scene recall.
Solved a problem in which signals from RPio622/RPio222 might not have been input.
Solved a problem in which the console firmware might have frozen when saving or loading the console data to a USB flash drive.
Solved a problem in which patched channel names would not appear on the Automixer screen.

Solved some minor errors.

Notices in version updating

The project file saving method has been changed from V1.20. When loading a project file saved by V1.16 or earlier, the patching of plug-ins may be unintentionally removed. If this happens, manually patch them again.
When updating the console’s firmware from V1.20 or earlier, the progress bar may stop at the 14/18 status, or an error may stop the updating process. If this continues for five minutes or longer, turn the power of the console to off and on, and then retry the firmware update.
When loading a project file saved by V1.21 and earlier, the RACK Focus status indicator on the SCENE screen may not light even if effect plug-ins or GEQs are the target of Focus Recall. To indicate the Focus status properly, open the SCENE SETUP (FOCUS) pop-up screen once, and then close it. After doing this, save the revised project file to remove this problem in the future.

Notices in version downgrading

Do not load a project file saved by V1.51 and later to a system running V1.21 and earlier. When loading, all plug-ins will be un-mounted in all Scenes including the current memory. In this case, re-mounting and setting up of parameters will be required.
When downgrading the firmware, be sure to initialize all systems after downgrading.
When loading data including the MixToInput settings of the V3.00 system, the MixToInput function will work in RIVAGE PM systems even of less than V3.00. However, be careful of the possibility of unwanted signal loops, etc.

Notices for usage

If you recall a Scene in which a very high HA gain was set, from a scene having a low HA gain, even if no signal is patched, a very loud pink noise signal is occasionally output for a few seconds.
When a certain type of USB keyboard is connected to the console, the following message may appear:
You must restart your computer to apply these changes [Restart Now] [Restart Later]
If this message is shown, remove this USB keyboard. It is not compatible with the console and cannot be used.
When a DSP mirroring failover occurs, if the DSP engine B is set to active, the Word Clock master will not change automatically. To prevent audio dropouts, do not turn off the power of the DSP engine A even after a failover occurs.
Make sure to connect only the RIVAGE PM Editor and RIVAGE PM StageMix to a network connector for a RIVAGE PM Editor, and not the PM Editor network of a different DSP engine.
The channel name LCD cannot display unconfirmed characters such as Japanese kanji used in the Dante channel labels.
If you are using a Dante card (HY144-D-SRC) in Synchronous (144io Sync SRC) mode, check the “Enable Sync to External” option only for the card that operates as the master on the Dante network.

PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("AGREEMENT") CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT.

BY DOWNLOADING, INSTALLING, COPYING, OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY ABORT USING THE SOFTWARE.

1. GRANT OF LICENSE AND COPYRIGHT

Subject to the terms and conditions of this Agreement, Yamaha hereby grants you a non-transferable license to use copy(ies) of the software program(s) and data ("SOFTWARE") accompanying this Agreement, only on a computer, smartphone, musical instrument or equipment item that you yourself own or manage. The term SOFTWARE shall encompass any updates to the accompanying software and data. The SOFTWARE is owned by Yamaha and/or Yamaha's licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions. While you are entitled to claim ownership of the storage media in which the SOFTWARE is stored and the data created with the use of SOFTWARE, the SOFTWARE will continue to be protected under relevant copyrights.

2. RESTRICTIONS

You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever.
You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the SOFTWARE.
You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other computers.
You may not use the SOFTWARE to distribute illegal data or data that violates public policy.
You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.
You may not use the SOFTWARE in any manner that might infringe third party copyrighted material or material that is subject to other third party proprietary rights, unless you have permission from the rightful owner of the material or you are otherwise legally entitled to use.
You may not engage in any act that are against the law, public order and morals.

Copyrighted data, including but not limited to MIDI data for songs, used by or obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe.

Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.
Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners in public without permission of the copyright owner.
The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner.

3. TERM

This Agreement becomes effective on the day that you agree with this Agreement and remains effective until terminated. If any copyright law or provision of this Agreement is violated, this Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such termination, you must immediately abort using the SOFTWARE and destroy any accompanying written documents and all copies thereof.

4. DISCLAIMER OF WARRANTY ON SOFTWARE

YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT USE OF THE SOFTWARE IS AT YOUR SOLE RISK. THE SOFTWARE AND RELATED DOCUMENTATION ARE PROVIDED "AS IS" AND WITHOUT WARRANTY OF ANY KIND. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. SPECIALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED.

5. LIMITATION OF LIABILITY

EXCEPT WHEN THE DAMAGE INCURRED DUE TO ANY CAUSE ATTRIBUTABLE TO YAMAHA, YAMAHA'S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. EXCEPT WHEN THE DAMAGE INCURRED DUE TO ANY CAUSE ATTRIBUTABLE TO YAMAHA, IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EVEN IF YAMAHA IS LIABLE, EXCEPT IN CASE OF WILLFUL MISCONDUCT OR GROSS NEGLIGENCE BY YAMAHA, YAMAHA'S TOTAL LIABILITY TO YOU FOR ALL DAMAGES, LOSSES AND CAUSES OF ACTION (WHETHER IN CONTRACT, TORT OR OTHERWISE) SHALL BE LIMITED TO DIRECT OR GENERAL DAMAGES AND SHALL NOT INCLUDE INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES, AND IN NO EVENT SHALL YAMAHA'S TOTAL LIABILITY TO YOU FOR ALL DAMAGES EXCEED THE AMOUNT PAID FOR THE PRODUCT USED WITH THE SOFTWARE.

6. OPEN SOURCE SOFTWARE

This SOFTWARE may include the software or its modifications which include any open source licenses, including but not limited to GNU General Public License or Lesser General Public License ("OPEN SOURCE SOFTWARE"). Your use of OPEN SOURCE SOFTWARE is subject to the license terms specified by each rights holder. If there is a conflict between the terms and conditions of this Agreement and each open source license, the open source license terms will prevail only where there is a conflict.

7. THIRD PARTY SOFTWARE AND SERVICE

Third party software, service and data ("THIRD PARTY SOFTWARE") may be attached to the SOFTWARE. IF, in the written materials or the electronic data accompanying the software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must abide by the terms of any agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof.

Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.
Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.

Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE.

U.S. GOVERNMENT RESTRICTED RIGHTS NOTICE:
The Software is a “commercial item,” as that term is defined at 48 C.F.R. 2.101 (Oct 1995), consisting of “commercial computer software” and “commercial computer software documentation,” as such terms are used in 48 C.F.R. 12.212 (Sept 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.72024 (June 1995), all U.S. Government End Users shall acquire the Software with only those rights set forth herein.

8. CHANGE OR END OF SOFTWARE

Yamaha may change the specification of the Software without notice to you.
Yamaha may end the supply or support of the Software without notice to you when Yamaha determines that it is difficult to continue supply of the Software accompanied by the end of manufacturing or sales of the products or service applicable to Software.

9. AMENDMENT

Yamaha may at its discretion amend, revise, or update this Agreement.
When Yamaha amends, revises, or updates this Agreement, Yamaha obtains your consent to the updated terms of this Agreement, or Yamaha specifies the amendment contents and the effective date and posts them on Yamaha's Website within a reasonable period of time before the effective date.
You may terminate this Agreement before the effective date in accordance with the way that Yamaha specifies if you don't agree with the amendment of this Agreement.

10. GENERAL

This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect. All legal notices, notice of disputes and demands for arbitration, and any other notice which purports to change these provisions or to assert legal entitlements must be sent in writing to:

Yamaha Corporation
10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, Shizuoka, 430-8650, Japan

11. ENTIRE AGREEMENT

This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement.

Last updated: July 10, 2024

Sí estoy de acuerdo

rivage_firm300.zip (475.8MB)