Descargas
PREGUNTAS FRECUENTES
-
What is the difference between DME64N and DME24N?
-
What is the difference between DME24N and DME4io-ES/C? Is it possible to use DME4io-ES/C for the similar purpose as DME24?
-
What is the difference between firmware V3.5x or earlier and V3.8 or later?
-
Is it impossible to use the Mini-YGDAI cards with DME that don't appear in the Device Property dialog in DME Designer?
-
Does the maximum number of input/output channels depend on the sampling frequency (fs)?
-
How can I input audio signal from a Microphone?
-
What is necessary to transfer digital audio signal between mixing console and DME64N/24N?
-
What is the advantage of cascading DME64N units together?
-
How far can cascade cables be extended?
-
What can I do by cascading the DME-N with the PM5D series or DM2000?
-
Which arbitary point can I listen to by using monitor function?
-
Why is the latency from input to output different among channels?
-
What kinds of data are contained in a Scene?
-
How many seconds does it take to recall a scene?
-
Can the scene memories of all DME-N units on the network be recalled simultaneously?
-
Is it possible to install both of DME Designer V3 and V4 into single PC and use them simultaneously?
-
DME-N Network Driver (Ether-MIDI Driver) cannot be installed with the error message of "An additional MIDI Driver cannot be installed on this computer."
-
Audio signal does not flow even though wires seem to be connected among components in DME Designer Configuration window. What's wrong?
-
Why is it sometimes possible to place components even when the DSP Resource Meter exceeds 100%?
-
DME and DME Designer don't go ONLINE state. What should I check?
-
The control speed from DME Designer is too slow. What's wrong?
-
Is it possible to import configuration data from a DME that has already been operating into a PC in order to revise its configuration?
-
Does the PC have to keep ONLINE with the DME unit?
-
Is it possible to connect multiple PCs to a single network and control the system from multiple DME Designers?
-
How long does it take to synchronize data between DME and DME Designer?
-
Is it possible to use DME Designer V4 in combination with DME-N firmware V3?
-
There are two different hardware specifications for DME: V3.5x or earlier; and V3.8x or later. Can they be used in the same system?
-
What methods are available to control a DME remotely or making a DME work in conjunction with other equipments?
-
What functionalities can be controlled from an external controller?
-
What are the spec for cable that can be used with control panels such as the CP4SF?
-
How far can the cable between a GPI controller and a DME be extended?
-
Can I connect multiple GPI switches to a single GPI IN?
-
Can I specify the minimum and maximum value for GPI IN?
-
GPI fader/volume controller does not work correctly. What should I check?
-
Please let me know about how to control a DME from an external controller via Remote/Ethernet.
-
In order to change the parameter continuously by using DME Remote Control Protocol, how frequently should the command be sent to the DME?
-
Can a DME64N/24N be controlled via Ethernet cable from an external controller?
-
How can I control a DME64N/24N using physical faders and switches on a mixing console?
-
What kind of switching hub can I use to connect among PC and multiple DMEs?
-
Is it possible for DME control network to co-exist with audio network such as CobraNet or EtherSound?
-
Is it possible to control a DME from DME Designer in an existing LAN where several PCs and other equipments are already connected?
-
How can I determine IP address assigned to a DME64N/24N?
-
What kind of cables fit the analog in/out Euroblock connectors on DME24N?
-
Does the ICP1 require a power supply?
-
How many languages can the DME-N's display show?
-
How can I initialize the DME internal memories?
-
How can I update the DME64N/24N firmware?
-
How can I upgrade my DME64N/24N V3.5x to V3.8x or V4.0x?
